Description / Abstract:
This specification covers three (3) types of hose, and two (2)
constructions of hose, 12.7 mm diameter, and larger, coupled and
uncoupled, for use with gasoline, oil, or diesel fuel in automotive
fuel systems. Drawing callouts not referencing a hose construction
are assumed to be referencing Construction 1. This hose is not
compatible with biodiesel fuel. Type A hose is intended for higher
stress applications.
Classification/Material Description. The hoses described in this specification are differentiated based on the reinforcement and the composition of the different layers into the following types and construction numbers.
Reinforcement to the tube may be applied by braiding, knitting or circular weaving.
•Type A: Reinforced with aramid fiber.
•Type B: Reinforced with rayon fiber.
•Type C: Reinforced with polyester and nylon in a knit wrap construction with alternating loops of polyester and nylon. Nylon must be looped through polyester.
Constructions 1: This hose shall consist of a smoothbore tube of butadiene/acrylonitrile (NBR) copolymer compound. The cover shall consist of chlorosulfonated polyethylene (CSM) or chlorinated polyethylene (CPE) compound. The cover may be perforated to facilitate degassing during manufacturing operations. Hose shall be black. The tube shall be reinforced with a yarn or cord applied by braiding, knitting, or circular weaving or of 2 ply counter directional helical winding.
Construction 2: This hose shall consist of an inner smoothbore tube of butadiene/acrylonitrile (NBR) copolymer compound. The reinforcement shall be an aramid fiber yarn or cord applied by braiding, knitting, or circular weaving or of 2 ply counter directional helical winding, centered between two (2) layers of NBR. The cover shall consist of butadiene/acrylonitrile (NBR) copolymer compound, the exact material as the inner tube. Construction 2 hose may only be used within an enclosed tank system.
Hose Marking. The hose shall be legibly marked with the following information in the sequence stated:
•Nominal inside diameter expressed as fraction of an inch (e.g., 1 in to ¼ in).
•GM specification number GMW16833 followed by type and construction (e.g., GMW16833 A1).
•Date code, hose manufacturer's code identification as designated by Rubber Manufacturers Association, and the manufacturing plant location code.
Such marking shall be printed parallel to the axis in vivid white or light blue block letters not less than 3 mm high and the open space between the specified markings shall not exceed 25 mm.
The date code shall consist of six (6) digits: The first two (2) digits shall represent the month (01 thru 12) of the year, the next two (2) shall represent the day of the month (01 thru 31), and the last two (2) shall be the last two (2) digits of the year.
Additionally, one or more colored tracers shall be incorporated into the wall of the hose identifying the hose manufacturer. The color(s) shall be as designated by the Rubber Manufacturers Association.
Parts conforming to this specification that are too short for the marking required in 1.1.5 shall be marked as specified by the purchaser's engineering department.
Dimensions and Tolerances. Hose furnished to this specification shall conform to the dimensions and tolerances shown in Table 1 for the size (nominal inside diameter) specified by the purchaser conforms to SAE J30 (SAE 30R7). Hose cover wall thickness shall be between 25% and 40% of total wall thickness.
Concentricity based on total indicator reading between inside bore of hose and outer surface of hose shall not exceed 1.3 mm.
Wall gage for sizes 31.75 thru 44.45 mm shall be between 4.3 mm and 5.6 mm and for sizes 50.80 thru 63.5 mm between 4.3 mm and 6.4 mm. Construction 2 hose shall have a hose wall tolerance of ± 1.2 mm.
Classification/Material Description. The hoses described in this specification are differentiated based on the reinforcement and the composition of the different layers into the following types and construction numbers.
Reinforcement to the tube may be applied by braiding, knitting or circular weaving.
•Type A: Reinforced with aramid fiber.
•Type B: Reinforced with rayon fiber.
•Type C: Reinforced with polyester and nylon in a knit wrap construction with alternating loops of polyester and nylon. Nylon must be looped through polyester.
Constructions 1: This hose shall consist of a smoothbore tube of butadiene/acrylonitrile (NBR) copolymer compound. The cover shall consist of chlorosulfonated polyethylene (CSM) or chlorinated polyethylene (CPE) compound. The cover may be perforated to facilitate degassing during manufacturing operations. Hose shall be black. The tube shall be reinforced with a yarn or cord applied by braiding, knitting, or circular weaving or of 2 ply counter directional helical winding.
Construction 2: This hose shall consist of an inner smoothbore tube of butadiene/acrylonitrile (NBR) copolymer compound. The reinforcement shall be an aramid fiber yarn or cord applied by braiding, knitting, or circular weaving or of 2 ply counter directional helical winding, centered between two (2) layers of NBR. The cover shall consist of butadiene/acrylonitrile (NBR) copolymer compound, the exact material as the inner tube. Construction 2 hose may only be used within an enclosed tank system.
Hose Marking. The hose shall be legibly marked with the following information in the sequence stated:
•Nominal inside diameter expressed as fraction of an inch (e.g., 1 in to ¼ in).
•GM specification number GMW16833 followed by type and construction (e.g., GMW16833 A1).
•Date code, hose manufacturer's code identification as designated by Rubber Manufacturers Association, and the manufacturing plant location code.
Such marking shall be printed parallel to the axis in vivid white or light blue block letters not less than 3 mm high and the open space between the specified markings shall not exceed 25 mm.
The date code shall consist of six (6) digits: The first two (2) digits shall represent the month (01 thru 12) of the year, the next two (2) shall represent the day of the month (01 thru 31), and the last two (2) shall be the last two (2) digits of the year.
Additionally, one or more colored tracers shall be incorporated into the wall of the hose identifying the hose manufacturer. The color(s) shall be as designated by the Rubber Manufacturers Association.
Parts conforming to this specification that are too short for the marking required in 1.1.5 shall be marked as specified by the purchaser's engineering department.
Dimensions and Tolerances. Hose furnished to this specification shall conform to the dimensions and tolerances shown in Table 1 for the size (nominal inside diameter) specified by the purchaser conforms to SAE J30 (SAE 30R7). Hose cover wall thickness shall be between 25% and 40% of total wall thickness.
Concentricity based on total indicator reading between inside bore of hose and outer surface of hose shall not exceed 1.3 mm.
Wall gage for sizes 31.75 thru 44.45 mm shall be between 4.3 mm and 5.6 mm and for sizes 50.80 thru 63.5 mm between 4.3 mm and 6.4 mm. Construction 2 hose shall have a hose wall tolerance of ± 1.2 mm.
